Pool Cover propose RIVIERA, un abri de piscine bas
Riviera est un abri de piscine bas
Riviera - Pool Cover - Abri de piscine bas
Riviera - Pool Cover: abri de piscine bas
RIVIERA, l'abri de piscine bas de Pool Cover




The RIVIERA pool enclosure is also known as the low pool enclosure. As its name indicates, its inside height from the lowest section is 90 cm. This height allows you to take full advantage of your pool and even to sit around it.

Ideal for keeping your pool water completely clean, warmer (+8 to 12°C) and secure.

Reliability and robustness: Most low pool enclosures present on the market are designed to comply with the snow load resistance standard imposed by the French Standard, which is 45 kg/m2. We believe that the height of the pool enclosure in no way alters the risks associated with snow load. As a result, we require our enclosures to have identical resistances, although our low pool enclosures are actually “small high enclosures”. The sections and parts by which our pool enclosures are constituted are identical. Our customers opt for the safety and reliability of the product, especially in areas exposed to snow.

The RIVIERA model, just like all other models of the range, is designed to provide a snow load resistance of up to 60kg/m2. We can increase the resistance up to 120 kg/m2 on demand.

The RIVIERA can be produced with sides with straight corners (also known as “3 angles”) or cut-off corners (also known as “5 angles”) optionally.

In its standard version, the RIVIERA model consists of “x” sliding sections, 1 fixed section, 1 tiltable front and 1 fixed rear.

Consider asking our technician about the many possibilities of ensuring that your RIVIERA pool enclosure is fully in keeping with your expectations. There is an almost infinite number of adaptations, as chosen by you.



  • (x) sections including 1 fixed section
  • 1 tiltable front “garage door” type with a sliding door in the narrowest section
  • 1 fixed rear with a sliding door in the widest section
  • The doors are fitted with key locks
  • The height of the brushes between the tiltable front and the floor is 50mm
  • The height of the brushes between the fixed rear and the floor is 50mm
  • The castors are made from polyamide and have a diameter of 100 mm. There are 8 per section.
  • The accessories are made from A2 stainless steel or aluminium
  • The anchors are A2 stainless steel cases with an M14 diameter and depth of 160mm
  • The anchors are attached by a 2-component chemical seal (epoxy)
  • The anchors are fitted with caps
  • The floor attachments consist of A2 stainless steel bolts with a butterfly head
  • The floor attachments of the first mobile section are fitted with keys
  • The side walls are fitted with SAN 4 mm transparent sheets
  • The roofs are fitted with PC translucent alveolar sheets (polycarbonate 6mm)
  • The seal between the sections consists of nylon brushes on a stainless steel backing.
  • The height of the first section is 0.90m and is measured at the cross beam and inside the enclosure (see drawings)
  • The theoretical length is always a multiple of 2.10 m. It is important to refer to the drawings to acknowledge the actual dimensions which are often greater than the theoretical dimensions.
  • Other dimensions and types of construction on demand.


  • Moving the sliding door in the front and/or the back
  • Changing the height of the brushes of the tiltable front and the fixed back
  • Raising of the fixed rear to allow it to move without scraping against the floor (large brushes)
  • Replacing the translucent roof sheets with OPALINE white sheets
  • Replacing the brushes between the sections with black EPDM seals
Important comments
  • There is a possible tolerance of 3% between the theoretical dimensions validated by the customer through the drawings and the actual dimensions of the delivered product. The seller and its customer must take this comment into account and consider the necessary tolerances at the installation site of the enclosure so that no difficulties are encountered.
  • The pool enclosure offered in this document is fitted with a light aluminium structure which is compliant with French Standard NF P90-309 and is able to resist a snow load equivalent to or less than 45 kg/m2. In the event of snow, it is important to clear the snow from the enclosure in order to avoid any risk of irreparable deformation.
  • Under no circumstances may the system of sliding modules on castors be assimilated with an airtight building, either at the level of the roof, the doors, the openings, the glazed surfaces, between the sliding sections and other joint systems.
  • The end customer will make sure that the support (floor) of the pool enclosure has a concrete stud which is at least 15cm thick at the level of its running rail.
  • In a bid to prevent the infiltration of rainwater via the ground, the end customer will make sure that there is a slope in the paving which begins at its highest point from inside to outside of the enclosure. In general, a slope of 1% is deemed to be sufficient.


RIVIERA 90 10.50M (5 SECTIONS) X 5.80M

Fixed rear with sliding door

Abri de piscine RIVIERA 90 - Fiche technique 1

Tiltable front garage door type with sliding door

Abri de piscine RIVIERA 90 - Fiche technique 2
Abri de piscine RIVIERA 90 - Fiche technique 3

Abri de piscine RIVIERA 90 - Pool Cover