GENÈVE abri de piscine haut - Pool Cover
GENÈVE - abri de terrasse
GENÈVE - abri de terrasse POOL COVER - VERANDAIR
Pool Cover - Verandair - GENÈVE
Abri de piscine GENÈVE
Couverture de piscine haut - Modèle Genève - Pool Cover
Modèle Genève - Pool Cover - Couverture de piscine haut
Modèle GENÈVE: abri de piscine haut
Modèle GENÈVE (Pool Cover) - Abri de piscine haut
Abri de piscine haut - Modèle GENÈVE (Pool Cover)
Pool Cover - Abri de piscine haut - Modèle GENÈVE
Abri de piscine haut - Modèle GENÈVE

HIGH LEAN-TO SWIMMING POOL ENCLOSURE – GENEVE

HIGH LEAN-TO SWIMMING POOL ENCLOSURE – MODEL GENEVE

Description

The high pool enclosure called GENEVE is also known as the high lean-to pool enclosure (lean-to = slides along a wall). A place offering genuine peace and quiet and satisfaction around your pool for you and your family. With direct access to your home, the GENEVE pool enclosure is an absolute must for your daily life!

Ideal for keeping your pool water completely clean, warmer (+8 to 12°C) and secure.

Reliability and robustness: The snow load resistance standard imposed by French Standards is 45 kg/m2. Our classic GENEVE pool enclosure is designed by our own in-house design office to exceed the standard. The GENEVE model, just like all other models of the range, with the exception of the PANAMA 120, is designed to provide a snow load resistance of up to 60kg/m2.

In its standard version, the GENEVE model consists of “x” sliding sections, 2 fixed sections and 2 fixed front.

This model can also be built onto a wall. In this case, we remove a fixed rear. It should be noted that this model has a central opening.

The GENEVE may be produced with sides with straight corners or cut-off corners optionally.

Consider asking our technician about the many possibilities of ensuring that your GENEVE pool enclosure is fully in keeping with your expectations. There is an almost infinite number of adaptations, as chosen by you.

Composition

THE GENEVE MODEL CONSISTS OF:

  • Central opening
  • 2 fixed rears with sliding door
  • The doors are fitted with key locks
  • The height of the brushes between the fixed rear and the floor is 50mm
  • The castors are made from polyamide and have a diameter of 100 mm. There are 8 per section.
  • The accessories are made from A2 stainless steel or aluminium
  • The anchors are A2 stainless steel cases with an M14 diameter and depth of 160mm
  • The anchors are attached by a 2-component chemical seal (epoxy)
  • The anchors are fitted with caps
  • The floor attachments consist of A2 stainless steel bolts with a butterfly head
  • The floor attachments of the first mobile section are fitted with keys
  • The side walls are fitted with SAN 4 mm transparent sheets
  • The roofs are fitted with PC translucent alveolar sheets (polycarbonate 6mm)
  • The seal between the sections consists of nylon brushes on a stainless steel backing.
  • The height of the first section is 2m and is measured at the cross beam and inside the enclosure (see drawings)
  • The theoretical length is always a multiple of 2.10 m. It is important to refer to the drawings to acknowledge the actual dimensions which are often greater than the theoretical dimensions.
  • Other dimensions and types of construction on demand.
Customisation

THE FOLLOWING IS POSSIBLE ON DEMAND (WITHOUT ADDITIONS):

  • Moving the sliding door to the end
  • Changing the height of the fixed rear brushes
  • Replacing the translucent roof sheets with OPALINE white sheets
  • Replacing the brushes between the sections with black EPDM seals
Important comments
  • There is a possible tolerance of 3% between the theoretical dimensions validated by the customer through the drawings and the actual dimensions of the delivered product. The seller and its customer must take this comment into account and consider the necessary tolerances at the installation site of the enclosure so that no difficulties are encountered.
  • The pool enclosure offered in this document is fitted with a light aluminium structure which is compliant with French Standard NF P90-309 and is able to resist a snow load equivalent to or less than 45 kg/m2. In the event of snow, it is important to clear the snow from the enclosure in order to avoid any risk of irreparable deformation.
  • Under no circumstances may the system of sliding modules on castors be assimilated with an airtight building, either at the level of the roof, the doors, the openings, the glazed surfaces, between the sliding sections and other joint systems.
  • The end customer will make sure that the support (floor) of the pool enclosure has a concrete stud which is at least 15cm thick at the level of its running rail.
  • In a bid to prevent the infiltration of rainwater via the ground, the end customer will make sure that there is a slope in the paving which begins at its highest point from inside to outside of the enclosure. In general, a slope of 1% is deemed to be sufficient.

EXAMPLE HIGH ENCLOSURE GENEVE

GENEVE 10.50M (5 SECTIONS) X 5.80M

2 fixed rears with sliding door

Abri de piscine haut GENÈVE - fiche technique 1
Abri de piscine haut GENÈVE - fiche technique 2
Abri de piscine mi-haut Boston - Fiche technique 3
Abri de piscine haut - modèle GENÈVE

“The lean-to enclosure” is truly an extra living room that is directly attached to your home…

Does going to and from your pool in dismal weather spoil your enjoyment? Do you shiver every time you cross your garden after a swim? Then the lean-to swimming pool enclosure is for you!

Elegant as it is, it complements your house and can be used as a veranda all year round.

Your opportunity to make your pool area an enjoyable and relaxing environment:

  • Stay out of the water and sit around the pool;
  • Read or just recline comfortably in your deckchair;
  • Play with the children in safety;
  • Chat with your family and friends…

As an extension to your house, with an unobstructed view of your garden. Enjoy a host of benefits:

Protection:

  • During bad weather;
  • The temperature increase in your pool;
  • Withstands strong wind, heavy rain and snow…

Safety:

  • Your children, grandchildren and family can play without fear;
  • Fitted with an anti-theft device to give you peace of mind.

Comfort and pleasure:

  • Impeccably clean water all the time;
  • Softer water from fewer maintenance products;
  • Sheltered from leaves and dirt.

Let the youngsters enjoy the garden. The POOL COVER swimming pool enclosure will bring you tranquillity and peace of mind.

POOL COVER offers you a swimming pool enclosure that is extremely robust and easy to use.

  • The lean-to telescopic swimming pool enclosure can be made in all sizes (length, width, height) and all colours. It is generally suitable for the majority of swimming pools.
  • They can be made with right-angle panels or cut-off corners.
  • The POOL COVER lean-to swimming pool enclosure can also be attached end-on to your home (without gable).
    You decide which way your cover will open. For example, it is possible to open it towards a single fixed section. In this case, all of the sections fold up on the same side.
  • It is also possible to have a central opening, in which case there are two fixed sections.

We will help you to select the swimming pool enclosure that suits you best: Lean-to telescopic swimming pool enclosures:

  • With or without rails, the lean-to telescopic swimming pool enclosure is easy to handle, with a sliding action on wheels and a guidance system fitted to the side of the structure (the drawer principle).
  • The enclosure can be opened manually or using a remote-controlled autonomous motor. This device can be installed later.
  • Thanks to its ‘accordion’ facade system (front and back), your pool is almost completely open as all of the sections fold into one.
  • You can have the sliding doors placed wherever you prefer. They can be fitted in the facades or on the sides.

All our enclosures and covers comply with the French standard NF P 90 309.